Home > Dvd Drive > Replacing DVD Drives - IDE To SATA

Replacing DVD Drives - IDE To SATA

Contents

Click Properties in the menu that displays. To its right is the SATA power plug. I've used Syba's IDE/SATA Converter. Label "A" is the SATA power connector, "C" is the "legacy" or IDE power connector, and "B" is the SATA data or "signal" plug.

Install a SATA drive If you are replacing an existing drive then the new drive will simply go in the same position (drive bay) as the old drive. Like PATA, the SATA specs have evolved quickly to improve data transfer. This page requires Javascript. To reduce the chance of ESD damage, work over a noncarpeted floor, use a static dissipative work surface (such as a conductive foam pad), and wear an ESD wrist strap connected

How To Connect Ide Dvd Drive To Sata Motherboard

Drive dongles like the Syba do not require device drivers. Alternatively, push the blank out from the inside. Master should be selected if this will be the only device on a single IDE cable or if it is the second device to be connected and the other device is

Another alternative is to buy an adapter card that plugs into the motherboard and has the sockets you need. Figure : IDE cable Slave connector (or second drive) Master connector (first drive) If the IDE cable was removed from the motherboard, connect the other end of the IDE cable into Sometimes you'll find that the drive ordering is hardwired, or that you can't boot from one drive. Dvd Drive Power Cable This picture shows the pieces in  Eforcity's PATA and SATA Converter Set: Eforcity's USB Connector Set (Eforcity and Amazon) You use your computers' USB port as the interface to connect your

Warnings Turn off and unplug your power supply to avoid the possibility of electrocution. How To Connect Dvd Drive To Motherboard Find a clear, flat, stable work surface over a floor that is not carpeted. Yükleniyor... look at this site Some CD/DVD writers work best when they are the master others work fine regardless, always consult the manufacturers instructions that came with your CD/DVD Writer.

You can see where the IDE data ribbon cable plugs in to connect it to the motherboard and where the Molex power plug goes. Optical Drive Power Cable Transition Drive Uses Either Power Plug  (Gateway) Inspect your motherboard, too. The red SATA data cable is plugged to connect to a SATA motherboard socket to support data transfer. How can I best mix IDE and SATA drives in one system?

How To Connect Dvd Drive To Motherboard

Back and Front of Syba's Drive Connector Special Power Plug & SATA Data Cable   (Syba and Amazon) Since the black connector attaches directly to the end of your disk drive, you Most motherboards have only PATA or SATA data connector sockets. How To Connect Ide Dvd Drive To Sata Motherboard CD/DVD writer back panel Note the section we have pointed out in fig 1.2 above, this is the jumper selection that depicts what the drive will be in the IDE configuration. How To Install Dvd Drive On Pc Switching to a SATA drive will reduce the bulk of cables in your computer, and SATA offers increased speeds for data transfer.

If using a PCI SATA controller card, connect the Serial ATA cable from the drive to a SATA slot on the controller card. Press in on the tabs attaching the front cover (three or four on each side), and gently pull it forward. Skip to main contenteBayShop by categoryEnter your search keywordAll CategoriesAdvancedHi (Sign in to bid or buy) Daily Deals Gift Cards Sell Help & Contact My eBayExpand My eBay Summary Bids/Offers Watch Just use the power plug you have, no worries. How To Install Cd Drive In Laptop

The marketing blurb says "burn the disk, flip it, then burn the label". More than likely its because I have no idea what it is called. Figure : Removing the side panel If the front of the case prevents you from removing the drive, remove the front cover. Most new motherboards have several SATA ports, but if yours does not, adapters are available for IDE ports.

MESSAGES LOG IN Log in Facebook Google Email No account yet? Ide To Sata Converter For Dvd Drive Learn More I've focused on readability so I've left out some technical details. Read your doc to see how your board works.

Write a guide db238e1a8bef9ec5e4f28e6ec9e04c9470992295 Explore more guides View previous Best DVD Burners Image Best DVD Burners Published by: suvi1774 Top 6 DVD RW Drives Image Top 6 DVD RW Drives Published

Currently it has a basic IDE CD ROM drive from the factory. Be careful not to dislodge the other cables, and make sure that the IDE cable fits snugly into its connector. Z7_3054ICK0KGTE30AQO5O3KA30H5 hp-country-locator-portlet Actions ${title} Loading... Sata Optical Drive Bu özellik şu anda kullanılamıyor.

Skip to Step 4 if you are adding a new drive without removing an existing drive. If the drive attaches to the computer with a plastic latch, snap and lock it into place. Installing an IDE drive Make sure the new drive is set to Cable Select or CS. If you are replacing the IDE drive with a SATA device then you can unplug the IDE cable from the motherboard.